GS1900 vulnerability survives Patch 2 firmware update
The GS1900 vulnerability allows attackers who can reach a switch's web management interface, the browser-based page used to administer it, to run commands without logging in. Those commands execute with root privileges, the highest level of control on the device. Binarly found that the exploit still works against Zyxel's earlier 2.90 Patch 2 firmware, and new 2.90 Patch 3 firmware is now available for 10 GS1900 network switches. A network switch is a device that connects computers and other equipment on the same network.
Patch 2 was identified in a June 16 advisory as the fix for CVE-2026-7273. Binarly reported the remaining flaw to the vendor on September 29 and describes it as a zero-day, meaning attackers had a working exploit before an effective fix was available. The issue is now tracked separately as CVE-2026-107441. Patch 3, which addresses that flaw, was posted on October 23 and announced in an advisory earlier this week. Firmware is the built-in software that controls a device.
The affected models and their required updates are: GS1900-8, from 2.90(AAHH.2)C0 or earlier to 2.90(AAHH.3)C0; GS1900-8HP, from 2.90(AAHI.2)C0 or earlier to 2.90(AAHI.3)C0; GS1900-10HP, from 2.90(AAZI.2)C0 or earlier to 2.90(AAZI.3)C0; GS1900-16, from 2.90(AAHJ.2)C0 or earlier to 2.90(AAHJ.3)C0; GS1900-24, from 2.90(AAHL.2)C0 or earlier to 2.90(AAHL.3)C0; and GS1900-24E, from 2.90(AAHK.2)C0 or earlier to 2.90(AAHK.3)C0. The remaining models are GS1900-24EP, from 2.90(ABTO.2)C0 or earlier to 2.90(ABTO.3)C0; GS1900-24HPv2, from 2.90(ABTP.2)C0 or earlier to 2.90(ABTP.3)C0; GS1900-48, from 2.90(AAHN.2)C0 or earlier to 2.90(AAHN.3)C0; and GS1900-48HPv2, from 2.90(ABTQ.2)C0 or earlier to 2.90(ABTQ.3)C0. Patch 2 and every earlier build need to be replaced with the listed Patch 3 build.
The security advisory provides no workaround for owners who cannot install Patch 3 yet. It also does not state whether updating removes access that an attacker may already have gained, or identify checks that owners should perform if compromise is suspected. Neither Binarly nor GreyNoise says that switches observed in earlier attacks were running Patch 2, and the vendor's advisory does not confirm that CVE-2026-107441 itself has been exploited.
Binarly says all 10 Patch 2 builds contain the flaw and that an attacker needs only network access to the management service. The vendor describes the threat as a LAN-based, unauthenticated attacker. LAN means the local network within a home or workplace, while unauthenticated means no valid username or password is required. Binarly gives the flaw a CVSS score of 9.8 out of 10, compared with 8.8 in the vendor's CVE entry. CVSS is a standard scale for rating vulnerability severity.
The flaw is an out-of-bounds write in the program that processes web requests. This means the program can be made to write information beyond the memory space reserved for it. The program stores request parameters, individual pieces of information sent to it, in a fixed area that can hold 140 parameters. Before Patch 2, it checked neither the size of each parameter nor how many had already been stored.
The exploit sends an oversized 140th parameter. That data runs beyond the storage area and overwrites the program's parameter counter. The following parameter is then written outside the intended area, enabling the attacker to replace the function the program is about to call with one that executes the attacker's command. Patch 2 added a counter check, but only after the oversized parameter had already been copied. At that point, the counter contains a value controlled by the attacker, so the check fails to prevent the next write. Binarly says the original exploit works on Patch 2 without modification.
The researchers tested the exploit with emulated firmware and physical hardware, although they did not identify the hardware model. The exploit's own supported-firmware list includes the Patch 2 build for the GS1900-24. According to Binarly, Zyxel said CVE-2026-7273 concerned the missing counter check and treated the absent parameter-size check as a separate vulnerability, CVE-2026-107441. Patch 3 checks the counter before copying a parameter and limits the amount of data copied, which Binarly says closes the flaw.
The U.S. Cybersecurity and Infrastructure Security Agency added CVE-2026-7273 to its Known Exploited Vulnerabilities catalog on September 21. The catalog, commonly called KEV, records flaws known to have been used in attacks. Federal agencies were told to install Patch 2 by September 24. That listing appeared on the same day GreyNoise publicly reported attacks that it associated with CVE-2026-7273.
GreyNoise said attackers collected data from 996 GS1900 switches around August 17. They downloaded a collection script to the devices and left the gathered material available for later retrieval. It included switch configurations, hashed root credentials, which are scrambled representations of passwords, and network information. Of the affected switches, 564 still used factory-default credentials. GreyNoise did not identify their firmware versions or explain how the attackers reached their management interfaces.
GreyNoise linked the activity to the same attackers as, or a group related to, Red Heron, which Acronis tracks as Chinese-speaking. Acronis had previously connected Red Heron with the JITTERLY backdoor in a campaign against Gitea servers. Binarly found the GS1900 exploit on September 17 in an openly accessible folder on a server that also directed JITTERLY. Its advisory says either Patch 2 was an ineffective repair for CVE-2026-7273, or the attacks used a separate flaw from the one listed by CISA.
Binarly plans to publish a smaller proof-of-concept version of the exploit, which is demonstration code showing that a vulnerability works. CISA's KEV data, last updated yesterday, did not include CVE-2026-107441. Organisations reviewing exposed switch management and patching practices can also use AEU-I for security-first IT, infrastructure and consulting, while Patch 3 remains the specific vendor fix for this GS1900 vulnerability.